#OLD REPUBLIC LIGHTSABER HILTS ACTIVATOR#

Ideally, the Jedi or Sith who created it would go into deep Meditation, poring over each individual component to be added and thus forging a connection with it through the Force. Nearly every lightsaber hilt was unique in its construction, born of the Force-user who created it and using whatever materials were at hand typically, such weapons were created over a span of months.

Galen Marek telekinetically assembles his lightsaber. In the New Jedi Order this restriction was not carried through, and Jedi of that era once again used a wide variety of gemstones that produced different-colored blades. In the wake of the New Sith Wars, however, the Jedi chose to limit their crystal harvesting to the frigid world of Ilum, which brimmed with Adegan crystals that only produced blue and green blades. In the pre- Ruusan Jedi Order, such crystals could be found within Force-sensitive locations from across the galaxy these were typically places that resonated with a powerful dark or light-side presence in the Force. Gathering the various components to construct a lightsaber was relatively simple, given the utilitarian nature of the materials involved typically, these were readily available commercially, with the exception of the crystals. Rounding out the components that went into a typical hilt were the handgrip connector and a sturdy belt ring. The power cell was in turn wrapped beneath the power field conductor, power vortex ring and an inert power insulator. The primary crystal mount was in turn connected to the diatium power cell, which served as the primary power source of the weapon.

#OLD REPUBLIC LIGHTSABER HILTS ACTIVATOR#

Within the crystal energy chamber below this lay the focusing crystals, the focusing crystal activator and the primary crystal which was attached to the primary crystal mount and situated between the lightsaber energy gate. Following the arc tip were mounted the blade energy channel which was nested amongst the cycling field energizers. Immediately below and mounted internally lay the blade arc tip, followed on the outside by the blade power adjustment and blade length adjustment knobs. From focusing lens to pommel cap, such components typically included a blade emitter shroud, magnetic stabilizing loop followed by a ring tuning flange to ensure that the activated blade did not in turn burn through the hilt. The disassembled inner components of a lightsaber hilt.ДЄ lightsaber hilt contained many components, all of which were hand-selected by the Force-user who constructed it and tuned to be in harmony with each other at the completion of the weapon's creation. In addition, other Force-using traditions, such as the Jensaarai, constructed lightsaber hilts. Despite two attempts to eradicate the Jedi, the technology of lightsaber hilts continued to live on as the Order that had originally supported them rose anew. Though double-bladed hilts were typically associated with the Sith, practitioners of the dark side of the Force, those who followed the light side occasionally preferred these over the commonly-accepted use of single hilts in battle. Both Orders saw the construction of a lightsaber hilt to be one of the primary stages of a being's development within their ranks, mostly signifying that a Padawan or apprentice was ready to ascend to the next level. His hilt was made from the wood of a Brylark tree, which is as strong as metal.Д«oth the Jedi and the Sith Order used lightsaber hilts the former regarding them as tools rather than weapons, while the latter sought to use their sabers to fuel their quest for power. There are many unique hilts, such as the lightsaber hilt of Gungi, a Jedi Initiate. Over the thousands of years that followed, power technology and indeed the construction of lightsaber hilts continued to evolve, eventually encompassing shotos, shorter hilts used in the off-hand, as well as double-bladed, curved-hilt, and dual-phase designs. Eventually these hilts evolved to only require a small belt-mounted pack, and again to a fully self-contained weapon system such designs saw service as early as 5000 BBY at the start of the Great Hyperspace War.

The first hilts were produced as early as the advent of the lightsaber itself, approximately 15,500 BBY though cumbersome and requiring a backpack-mounted power source, the Jedi Order nonetheless began to embrace the technology. A combination handgrip, blade emitter, activator switch and power source, it held within the inner workings of the weapon that allowed it to produce its distinctive energy-based blade. Lightsaber hilts were the basic, all-encompassing part of a lightsaber. ' Touch the brightly-colored button up there by the pommelвЂ¦.' вЂ• Obi-Wan Kenobi

Old republic lightsaber hilts